Henry

36 / 124

SAFETY DEVICES
Visit our website:
Part No Type NPT (inch) Dimensions (inch) STD Rupture Disc setting
at 72°F (PSI)
Capacity
lbs. Air/min
Weight
(lbs) Inlet Outlet A B ØC D
5525-235-CE
Brass 3/8 3/8 2.94 1-1/4 Hex 0.375 0.79
235 25.5
0.69
5525-300-CE 300 32.2
5525-350-CE 350 37.3
5525-400-CE 400 42.5
5525-450-CE 450 47.6
5525-600-CE 600 63.0
5525-650-CE 650 68.1
5526-235-CE
Brass 1/2 1/2 2.62 1-1/4 Hex 0.500 0.79
235 45.3
0.68
5526-300-CE 300 57.2
5526-350-CE 350 66.3
5526-400-CE 400 75.5
5526-450-CE 450 84.6
5526-600-CE 600 110.8
5526-650-CE 650 119.8
5626-150-CE Stainless
Steel 1/2 1/2 2.96 Ø1.13 0.500 0.92
150 29.8
0.62 5626-250-CE 250 52.1
5626-300-CE 300 57.2
5627-150-CE Stainless
Steel 3/4 3/4 3.29 Ø1.50 0.750 0.92
150 35.8
1.44 5627-250-CE 250 57.7
5627-300-CE 300 68.7
5628-150-CE Stainless
Steel 1 1 3.73 Ø1.72 1.000 1.27
150 67.1
1.36 5628-250-CE 250 108.2
5628-300-CE 300 128.7
5629-150-CE Stainless
Steel 1-1/4 1-1/4 3.84 Ø1.98 1.312 1.27
150 91.4
1.56 5629-250-CE 250 147.2
5629-300-CE 300 175.2
Selection Guidelines
1. The Rupture Disc pressure setting should be the same as the Henry
Technologies’ Pressure Relief Valve setting.
2.
3. The stamped burst pressure is subject to a manufacturing tolerance of +/-
5%. This tolerance should be taken into account when specifying a
Rupture Disc setting (refer to table).
The stamped capacity of a spring loaded Pressure Relief Valve when
installed with a Rupture Disc between the inlet of the valve and the vessel
shall be multiplied by a factor 0.90 of the rated relieving capacity of the
Pressure Relief Valve alone.
4. It is recommended that the maximum operating pressure of the system is
no more than 70% of the stamped burst pressure, in order to minimize the
risk of premature fatigue failure of the disc. If operating pressures exceed
90% of the stamped burst pressure, the Rupture Disc should be replaced
immediately.
5. The design fatigue strength of each Rupture Disc is 100,000 pressure
cycles. Fatigue life will be reduced by excessive pressures or
temperatures, corrosion, damage, etc.
ΠInlet
 Oulet
Ž Gauge port, 1/8 NPT
 Rupture disc
D
B
3
A
3
4
Ø C
1
2
Rupture Disc manufacturing tolerance
Pressure setting (PSI) Pressure range (PSI)
150 143 - 158
200 190 - 210
235 223 - 247
250 238 - 263
300 285 - 315
350 333 - 368
360 342 - 378
400 380 - 420
450 428 - 473
600 570 - 630
650 618 - 683
36